宁波卧式模头射蜡机(16T)
设备名称：卧式模头宁波射蜡机(16T)
设备编号：TQ-8004
设备简介：
1.传统蜡缸式免换蜡缸式之改良机种，再配备蜡温均匀，出蜡稳定之供蜡系统(1对1)
2.表面无缩凹，无气泡，填充饱满，效率高
3.每天700~900模/台(8小时2工位)
4.储蜡桶除了保温蜡外，还提供热煤油给供蜡系统用，不但节省电费，还可因为热煤油有流动减少积碳，特殊热煤油回路设计，蜡均温性达90%.
5.射蜡机操作系统简单明了，所有参数设置匀为数字式
6.三段温度控制蜡温
7.射蜡压力为三段压力，解决产品凹陷问题
8.蜡桶储蜡量大为200L
9.蜡桶配有超温脱扣开关，防止超温引发火灾。
10.合模行程采用快、慢速装置，提高生产效率。
参数配置：
基本参数Bask parameters | ||
置模部分 Mold setting part | 合模压力Clamping pressure | 16T |
合模缸径Mold closing cylinder diameter | φ140 | |
压板尺寸Pressing plate size | 500*785*45(mm) | |
置模下板尺寸Dimension of lower plate for mold setting | 500*820*60(mm) | |
合模行程Clamping stroke | ST450mm | |
最大开距Maximum opening distance | 460mm | |
最小开距Minimum opening distance | 145mm | |
置模宽度(左右)Mold setting width (Left and right) | 540mm | |
置模深度(前后)Mold setting depth(Before and after) | 470mm | |
工作台尺寸Tabie size | 200*1480mm | |
液压部分 Hydraulic part | 泵流量及压力Flow and pressure of hydraulic pump | 40L/140KG |
液压电机Hydraulic motor | 3.75KW | |
液压油型号Hydraulic oil model | 68# | |
电磁阀Solenoid valve | 台湾Taiwan | |
油泵Oil pump | 台湾Taiwan | |
射蜡部分 Wax injection part | 挤蜡动作Wax squeezing action | 二段式Two-stage type |
挤蜡压力Wax extrusion pressure | 5~60KG | |
一次最大射蜡量Maximum wax injection amount at one time | 4.5L | |
射蜡流量Wax injection flow | 0-0.5L/S | |
储蜡桶容积Volume of wax storage barrel | 200L | |
储蜡桶加热功率Heating power of wax storage barrel | 2*2KW(4KW) | |
储蜡桶加蜡方式Wax filling method of wax storage barrel | 手动/自动Manual/Automatic | |
射嘴孔径Nozzle aperture | φ6.8mm | |
蜡温控制精度Wax temperature control accuracy | 正/负0.1℃ Positive/negative 0.1℃ | |
抽蜡油缸缸径Diameter of wax extraction cylinder | φ80mm | |
抽蜡油缸轴径Diameter of wax extraction cylinder shaft | φ40mm | |
抽蜡缸缸径Diameter of wax extraction cylinder | φ63mm | |
抽蜡缸轴径Diameter of wax extraction cylinder shaft | φ40mm | |
挤蜡油缸缸径Cylinder diameter of wax squeeze cylinder | φ125mm | |
挤蜡油缸轴径Diameter of wax squeeze cylinder shaft | φ60mm | |
挤蜡缸活塞直径Diameter of wax squeeze cylinder piston | φ125mm | |
挤蜡缸缸径Diameter of wax squeeze cylinder | φ125mm | |
射嘴上下调整距离Up and down adjustment distance of nozzle | 250mm | |
射嘴进退调整距离Adjustment distance of nozzle advance and retreat | 230mm | |
射嘴左右调整距离Left and right adjustment distance of nozzle | 400m | |
射嘴到压板中心距Center distance from nozzle to pressing plate | 最短Minimum 50mm | |
